NPC1 has been shown to act as an invasion receptor for Ebola and Marburg viruses, suggesting a direct role for NPC1

xO-D47E DluxM, DluxS, cqsA::Cmr DluxN, luxQ::Tn5, cqsA::Cmr DcqsA, DluxQ, pBB1 DkdpFABCDE thi rha lacZ nagA trkA405 trkD1 atp706 luxS::Tet -derivative of E. coli W3110 recA1 endA1 gyrA96 traD36 thi hsdR17 supE44 l2 relA1 D/F’ proA+B+ lacIq lacZDM15 kdpD in pKK223-3 pPV5-1 with KpnI site after the start codon of kdp luxN in pPV5-10 luxQ in pPV5-10 luxP in pGEX-4T1 luxU in pQE30 luxS in pQE30 pfs in pQE30 cqsA in pGEM-T-Easy r Reference This work This work This work MedChemExpress LY2109761 Analytical procedures Protein concentrations were determined by the method of Peterson using bovine serum albumin as standard. Proteins were fractionated by SDS-PAGE. His-tagged Lux proteins on immunoblots were labeled with mouse monoclonal antibodies directed against the His-tag and detected by incubation with alkaline phosphatase-conjugated anti-mouse IgG according to the manufacturer’s instructions. Quantitative Western blots were scanned with 300 dpi resolution in 256 gray scales and imported as TIFF files into ImageQuant 5.0. The amount of Lux proteins associated with membrane vesicles was quantified by comparison with the total amount of purified His-tagged LuxN. Determination of autoinducer concentrations in cell-free culture medium HAI-1 was quantified by UPLC using an Acquity UPLC System with a 2996 PDA detector controlled by Empower software. The system was equipped with an Acquity 2.16100 mm BEH C18 column packed with 1.7-mm particles, which was maintained at a constant temperature of 60uC. The Sample Manager was kept at 27uC. Aliquots of sample were injected via a partial loop with needle overfill, and all samples were analyzed three times. Water containing 3% acetonitrile served as the mobile phase, and isocratic elution was applied at a flow rate of 0.9 mLmin21 causing a back-pressure 16699066 of 770 bar. Detection was performed at 195 nm with 18946542 a scan rate of 20 Hz. The analysis time for each injection was set to 3 min, and all sample constituents were eluted from the column. The retention time for HAI-1 and the UVVis spectra of the peak provided the criteria for identification of the compound and assessment of its purity. A standard solution of HAI-1 was used for calibration and quantification of the analyte. Autoinducers as Timers Chromatograms were acquired with CHROMATOF software 1.00, Pegasus driver 1.61. Selective ion traces and peak heights were extracted from the NetCDF CHROMATOF export, and processed using the TagFinder software. Compounds that accumulated were filtered according to significance using Students t-test and the KruskalWallis test. The mass spectrum of modified CAI-1 was generated under manual supervision by automated deconvolution. Replicate mass spectra and retention indices were uploaded to the Golm Metabolome Database, . Available compound information may be retrieved from http://gmd.mpimp-golm.mpg. de/search.aspx using the ��A��identifier code. The fitted line for the CAI-1 concentration presented in generated using the x{12:6 f ~118:7z537:4= 1ze{ 0:7. was following equation: Synthetic autoinducers HAI-1 was purchased from the University of Nottingham and dissolved in a minimal volume of acetonitrile, diluted with water to a concentration of 100 mM and stored at 220uC. DPD, the precursor of AI-2, was synthesized in vitro using S-adenosyl-homocysteine and the enzymes LuxS and Pfs, followed by purification over boric acid resin. LuxS and Pfs were produced heterologously in E. coli JM109 transformed with plasmid pQE30LuxS-6His or pQE30Pfs6His, respect

Leave a Reply